 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PSMPS65 Series Single Output Up to 65 Watts AC/DC Medical Power Supply FEATURES Medical Application Low Cost, High Reliability Compact Size, Light Weight 100% Full Load Burn-In Test Universal AC Input / Full Range UL2601-1, EN60601-1 Approved Built-In EMI Filter, Low Ripple Noise High Efficiency, Low Working Temperature Protections: Short Circuit /Overload /Over Voltage SPECIFICATIONS: PSMPS65 Series All specifications are based on 25 C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. INPUT SPECIFICATIONS Input Voltage 90 - 264VAC (127 - 370VDC) Input Frequency 47 to 440Hz AC Current (typical) 1.6A @ 115VAC / 0.9A @ 230VAC Inrush Current Cold start 15A @ 115VAC; 30A @ 230VAC Leakage Current Less than 0.3mA @ 264VAC OUTPUT SPECIFICATIONS Output Voltage See Table Voltage Tolerance 2.0% typical Output Adjustment Range 10% rated output load Output Power 72W max with 18CFM minimum forced air flow Line Regulation 1% Load Regulation 2% typical Output Current See Table Ripple & Noise (20MHz BW) 100mVp-p typical Setup, Rise Time 800ms and 30ms @ 230VAC and full load / 800ms and 30ms @ 115VAC and full load Hold-Up Time 50ms @ 230VAC and full load / 16ms @ 115VAC and full load. Temperature Coefficient 0.04%/C (0~50C) PROTECTION Over Voltage Protection CH.1: 115~135% rated output voltage Overload Protection 73~105W hiccup mode, auto-recovery GENERAL SPECIFICATIONS Switching Frequency (fixed) 45KHz Efficiency Up to 80% Isolation Voltage (Input to Output) 4000VAC for 1 min. Isolation Voltage (Input to Field Ground) 1500VAC for 1 min. Isolation Resistance (Input to Output) 100M / 500VDC ENVIRONMENTAL SPECIFICATIONS Operating Temperature -10C to +60C (refer to derating curve) Storage Temperature -20C to +85C Operating Humidity (non-condensing) 20% to 90% RH Vibration 10~500Hz, 2G 10min./1cycle, Period for 60 minutes each along X, Y, and Z axes. MTBF 359,700 hours min. (According to MIL-HDBK-217) at 25C PHYSICAL SPECIFICATIONS Weight 280g Dimensions 127(L) x 76(W) x 42(H) mm SAFETY & EMC Safety Standards UL2601-1, TUV EN60601-1, IEC601-1 Approved EMC Standards EN55011 class B, EN61000-4-2,3,4,5,6,8,11, EN61000-3-2,3, EN60601-1-2, ENV50204 o Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSMPS65 Series Single Output Up to 65 Watts AC/DC Medical Power Supply OUTPUT VOLTAGE / CURRENT RATING CHART Model PSMPS65-3.3 PSMPS65-5 PSMPS65-7.5 PSMPS65-12 PSMPS65-13.5 PSMPS65-15 PSMPS65-24 PSMPS65-27 PSMPS65-48 Input Voltage Output Voltage 3.3 VDC 5 VDC 7.5 VDC 12 VDC 13.5 VDC 15 VDC 24 VDC 27 VDC 48 VDC Output Current Range 0 - 15.2A 0 - 13.8A 0 - 9.6A 0 - 6A 0 - 5.4A 0 - 4.8A 0 - 3A 0 - 2.7A 0 - 1.5A Output Current 12A 12A 8A 5.2A 4.7A 4.2A 2.7A 2.4A 1.35A Ripple & Noise 80mVp-p 100mVp-p 100mVp-p 100mVp-p 100mVp-p 100mVp-p 100mVp-p 100mVp-p 100mVp-p Rated Output Power 39.6W 60W 60W 62.4W 63.5W 63W 64.8W 64.8W 64.8W 90~264 VAC (127~370 VDC) NOTES 1. All parameters are specified at 230VAC input, rated load, 25C ambient. 2. Tolerances include set up tolerance, line regulation, load regulation. 3. Line regulation is measured from low line to high line at rated load. 4. Mounting holes M1 and M2 should be grounded for EMI purposes. 5. Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uF & 47uF capacitor. BLOCK DIAGRAM DERATING CURVE STATIC CHARACTERISTICS Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSMPS65 Series Single Output Up to 65 Watts AC/DC Medical Power Supply MECHANICAL DRAWING Unit: mm AC Input Connector (CN1): Molex 5277-02 or equivalent Pin. No 1 2 Assignment AC/N AC/L Mating Housing Molex 5195 or equivalent Terminal Molex 5194 or equivalent DC Output Connector (CN2): Molex 5273-06 or equivalent Pin No. 1,2,3 4,5,6 Assignment +V -V Mating Housing Molex 5195 or equivalent Terminal Molex 5194 or equivalent Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 |
Price & Availability of PSMPS65-12
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |